Blackstar St. James 100 Guitar Amplifier
Pay in instalments with ESTO
Couldn't load pickup availability
Description
Description
Blackstar St. James 100 Guitar Amplifier
The 100 W RMS power stage combines two 6L6 and two EL34 valves. Run both pairs together or select either pair in 50 W mode, then vary Power continuously from 100% down to 5%.
Clean draws on mid-1960s American clean tones, while Crunch offers early-1960s British character from warm cleans to responsive breakup. Crunch Boost adds a 10 dB clean boost ahead of the valve preamp.
OD 1 delivers classic overdrive; OD 2 increases saturation with a looser, resonant low end. Tight changes EQ before and after the overdrive stages. Four channels plus Boost and Tight give six voices.
An internal reactive load allows the valve power stage to operate without a cabinet. SILENT disconnects the speaker outputs and automatically sets minimum power, disabling the Power control. The black head has no built-in speaker.
Main Features
- Clean / Crunch share Bass, Middle and Treble knobs but use electrically independent circuits tuned for each channel; Crunch Middle provides active mid cut and boost. OD 1 / OD 2 use a separate shared EQ group.
- Channel Volume and Gain controls balance levels. Clean Bright and Presence for each channel group fine-tune the highs. Each group has its own Reverb control, with further editing in Architect.
- Solo boost adjusts over +2–6 dB and works on any channel. The rear Cut switch offers 0 / −1 / −2 positions for progressively reducing the highest frequencies.
- Switch the effects loop between Series and Parallel and select +4 dBu / −10 dBV level. In Parallel mode, turn off the external effect’s dry signal to avoid phasing.
- Select three stored CabRig settings on the amplifier; Architect edits virtual cabinets, microphones and room settings. Master affects speaker, XLR, headphone and USB output levels.
- The included FS-23 connects over XLR and controls channels, voices, Solo and Reverb. Architect reassigns switches 5 and 6; an optional FS-15 selects the four channels. MIDI In and Thru integrate external MIDI control.
Technical Specifications
- Power: 100 W RMS; EL34 or 6L6 pair in 50 W mode
- Valves: 3 × ECC83, 2 × 6L6, 2 × EL34
- Channels: 4: Clean, Crunch, OD 1, OD 2; 6 voices in total
- Speaker Loads: 1 × 16 Ω on its own socket, or 1 × 8 Ω / 2 × 16 Ω on the other socket group
- CabRig Outputs: Balanced mono XLR; 6.35 mm TRS stereo Line Out / Phones; USB-C
- USB Recording: 4 channels: 1–2 CabRig stereo mix, 3–4 separate CAB 1 and CAB 2 cabinet and microphone signals without EQ, mix or room processing
- Other Connections: 6.35 mm guitar input; mono Send / Return; FS-23 XLR; FS-15 TRS; 5-pin MIDI In / Thru; Kensington slot
- Logo Power: 9 V DC, up to 20 mA, for a St. James cabinet LED logo only
- Dimensions (W × H × D): 495 × 241 × 228 mm
- Weight: 10.1 kg
- Power Supply: 100–240 V AC, 50/60 Hz
Do not use both speaker socket groups simultaneously. Select SILENT for silent recording; disconnect a speaker cable at the amplifier end when removing it. USB uses standard computer audio drivers.
What’s Included
- 1 × Blackstar St. James 100 Guitar Amplifier
- FS-23 six-button footcontroller
- Region-appropriate mains cable
USB-C cable is not included. Choose a cabinet separately.
Who Is It For
For stage and studio playing from clean guitar tones to saturated overdrive. Adapt power, channel and valve-pair settings to the playing situation, then use CabRig and the reactive load for silent recording.
Can’t find the Blackstar product you are looking for?
Contact us: info@stageiq.lt or +370 636 55536.





